On A Roll — Howards’ Billet Roller Rocker Arms For LS Engines

When it comes to the LS engine family, one thing there is no denying is that GM developed what might be the best OEM slider-tip rocker system, ever. We’ve seen (and used) OEM and OEM-style rocker arms in a lot of LS applications over the years. However, that’s not to say they are perfect. Far from it, in fact. Especially when we’re maximizing every component of the engine. Enter Howards Cams and its billet-aluminum roller-rocker arm kit for the LS family of engines.

For over 70 years, Howards Cams has been building cams and valvetrain components for high-performance engines. So it only stands to reason that the team’s experience eschewed the “good enough” mantra that surrounds the OEM-style LS slider-tip rocker arms and decided to go the more traditional route, developing a full-roller rocker arm for LS applications. If you’re a small-block Chevrolet fan, these rocker arms appear to have a host of differences over stock. You might notice some similarities if you’re a fan of other brands (*cough* the Blue Oval *cough*).

Here you can see the Howards billet aluminum roller rocker arm compared to the OEM cast steel slider-tip rocker arm. Besides the obvious differences, there are a host of improvements you can’t see, as well, like the needle-bearing trunion and the needle bearings used in the roller-tip axle shaft.

Body Of Strength

When discussing valvetrain components, the age-old conundrum is balancing the weight of the rocker arms with stiffness. Since the rocker arms have to move back and forth several thousand times per minute, coming to a complete stop at each end of its travel, weight is important (inertia and all). However, resisting the urge to bend when there are forces being applied at either end of the rocker arm, simultaneously, is also a critical design feature.

In order to balance both weight and stiffness, Howards has designed a rocker body out of billet aluminum, which is anodized in the company’s signature purple color after heat treatment. ““Howards Rocker arm bodies are made from 7000-series aerospace grade aluminum for maximum strength and minimum weight,” says Howards’ Eric Bolander.  The aluminum rocker body offers ample stiffness, and reduced weight is one of aluminum’s inherent physical properties.

Because the Howards engineers are in complete control of the rocker arm design, they are able to produce the rocker arm bodies in both the factory 1.7:1 ratio, and an upgraded 1.8:1 ratio, for a little extra lift and duration from a given cam design. Additionally, the rocker bodies are designed to install with no special modifications to the cylinder heads and work with most standard valve covers. “Howards Rocker arm bodies are 100-percent CNC ground to factor out human error,” shares Bolander

Here you can see the hardened steel insert, which allows the pushrod to actuate the rocker arm without any steel-on-aluminum wear issues.

However, aluminum is inherently less wear-resistant than steel, so a pushrod, hardened or not, rubbing in the pushrod tip pocket would quickly wear into the aluminum body. So Howards fit the tip pocket with a hardened steel wear cup for the pushrod tip to ride on. On the other end of the rocker, a hardened steel roller wheel and axle shaft are fitted into the aluminum rocker body. The roller tip’s axle is fitted with needle bearings, which allows for much less friction across the face of the valve stem, especially compared to a slider tip design.

Enhancing The Fulcrum Of The Roller Rocker Arms

One potential source of consternation for all rocker arms is the fulcrum point. It has a big job in the overall scheme of things, not only having to support valvetrain loads, but also to rock back and forth, smoothly and reliably under those loads. That is no small ask. In order to both carry the loads of a higher spring rate and higher RPM, Howards has opted for a needle roller bearing setup surrounding a hardened-steel trunnion shaft.

Like the OEM rocker arm design, the Howards rocker arms use a fixed pedestal mount as opposed to a stud mount with a polylock nut, like a lot of aftermarket rocker arms before it. However, unlike the OEM pedestal mounts, the Howards rocker arms use a pedestal mount that you might be very familiar with if you have ever messed with late-model 5.0-liter small-block Fords.

On the left, you can see the OEM rocker stands (top) versus Howards Cams pedestals and link bar. The OEM fastener us used in both applications, with the flats milled in the aftermarket pedestals engaging the link bar to prevent rotation of the rocker arm and ensure proper alignment.

Instead of the factory LS pedestal mount that spans the entire cylinder head, each rocker arm uses an individual cylindrical pedestal mount that sits in a siamesed tray at the base of the pedestal to prevent rotation. The rockers bolt down with the factory rocker bolts, at the factory 22 lb-ft of torque. Like the factory arms, there is no adjustability, but there is also no need for adjustability, as the Howards rocker arms are designed to work with all of the stock LS valvetrain components while being able to handle upgraded spring pressure and aggressive cam profiles as well.

Howards Cams’ rocker arms are made in the USA and have a lifetime warranty to the original purchaser. All of these features add up to a stout rocker arm upgrade for LS-based engines. Just because the stock rocker arms on LS engines are good, doesn’t mean there isn’t room for improvement, as these billet aluminum rocker arms show.

As is clearly marked, these rockers are the factory 1.7:1 ratio. Howards also offers the rocker arms in a 1.8:1 ratio, for a little extra lift and duration from your camshaft.

Article Sources

About the author

Greg Acosta

Greg has spent twenty years and counting in automotive publishing, with most of his work having a very technical focus. Always interested in how things work, he enjoys sharing his passion for automotive technology with the reader.
Read My Articles

Hot Rods and Muscle Cars in your inbox.

Build your own custom newsletter with the content you love from Street Muscle, directly to your inbox, absolutely FREE!

Free WordPress Themes
Street Muscle NEWSLETTER - SIGN UP FREE!

We will safeguard your e-mail and only send content you request.

Street Muscle - The Ultimate Muscle Car Magazine

streetmusclemag

We'll send you the most interesting Street Muscle articles, news, car features, and videos every week.

Street Muscle - The Ultimate Muscle Car Magazine

Street Muscle NEWSLETTER - SIGN UP FREE!

We will safeguard your e-mail and only send content you request.

Street Muscle - The Ultimate Muscle Car Magazine

streetmusclemag

Thank you for your subscription.

Subscribe to more FREE Online Magazines!

We think you might like...


fordmuscle
Classic Ford Performance
dragzine
Drag Racing
chevyhardcore
Classic Chevy Magazine

Street Muscle - The Ultimate Muscle Car Magazine

Thank you for your subscription.

Subscribe to more FREE Online Magazines!

We think you might like...

  • fordmuscle Classic Ford Performance
  • dragzine Drag Racing
  • chevyhardcore Classic Chevy Magazine

Street Muscle - The Ultimate Muscle Car Magazine

streetmusclemag

Thank you for your subscription.

Thank you for your subscription.

Street Muscle - The Ultimate Muscle Car Magazine

Thank you for your subscription.

Thank you for your subscription.

Loading